Electronic Alarms and Home Security Devices - Lynxr-en all programming gone must have reset it

I have a Lynxr-en that I have used for about 1 1/2 years I had everything set up and I bought a 5804 keyfob and tried to set it up and I never could get it to work.
*56
zone were 30'31'32'33
zone type 23'22'21'20
report code 10'10'10'10
input code 5'5'5'5
loop button 1'2'3'4
All in order from top to bottom I entered the ser.number all 4 zones had an L where I thought they should nothing worked so I deleted them and kept trying I went to *83 and tried it there and never could get the 5804 fob to do anything so I went to *84 voice programming and must have pushed something there in the Template (default Table) or something because when I went to set my alarm in away mode nothing happened. I woud push my _ _ _ _ master code then away button and it wouldn't take. I went back and re entered my mastercode with the 4112+8+02+ _ _ _ _ and got it to work but now when I set it to away my motion sensor's don't work like the should and it used to give you time to exit but now when I enter the away its ready then only the red light is on in away mode I think that the red and green use to be on before. Do you think it deleted all my sensors since it did my master code ? and how can I check to be for sure since I lost my work sheet from the last time I installed theis stuff I don't know what zones they are set to. Anyone have any idea on what I did to cause this and how do I get set back up .Please Any help would be great. Thanks:confused::confused:

Yes, you could have easily stumbled into the system default command. You are going to have to start from scratch.

I'm trying to start over I have 3 5890 Motion Detecors that I have used without any trouble and now everytime I get them enrolled I get a Fault for each of them now and I'm just lost on where I'm going wrong. I them set as this.
(1) zone 05-zone type 04-alarm code 10-input 3 RF-Loop 1
(2) zone 07-zone type 04-alarm code 10-input 3RF-Loop 1
(3) zone 08-Zone type 04-alarm code 10-input 3RF-Loop 1
I set them up in *56 all three have been enrolled and have location names.As soon as I exit I get a lot of beeping with Fault 05-Fault 07-Fault 08. I did not enter serial number manually. I do remeber it beeping several times when enrolling each. Anyone have an Idea where I may have messed up.

List out the step by step you were doing to try to enroll one of the motions. I suspect that you are skipping or mis reading one of them, which is probably the same thing that was keeping you from enrolling the keyfobs, successfully.

I got them enrolled I hate to say this but I was faulting them myself I did not put the cover on real good after I just about gave up I figured out what was going on. The keyfob I still haven't got to work yet and I still like my glassbreaks I know the Input Type is 3 Rf-and Loop is 1 But I can't remember what I used for report code I think 10 does this sound right and zone type I don't know. Any clues would be great.Thanks

To start
4112 800 then *56
I press 30 then * -zone-A30
I press 23 then *-zone type-b23
I press 01 for 10 then *-Report code-c10
I press 5 then *-Input code-d5
I press 1 then * Loop number-E1 -press * 1A
I then press 1 and get 1b I enter the _ _ _ _ _ _ _ seven serial numbers then * then I press the 3 to check the serial numbers to make sure they are correct and they are the ones I entered
Then I press * because A31 is there .Zone -A31
Then I press 22 then * zone type-b22
I press 01 for 10 then * report code-c10
I press 5 then * Input code-d5
I press 2 then * Loop number-E2
I then press 2 for copy of the serial number then I press 3 to check ser.num. and they are correct.
I press * at A32--zone-A32
I press 21 then * zone type-b21
I press 01 for 10 then * Report code-c10
I press 5 then * Input code-d5
I press 3 then* Loop num.-E3
I then press 2 for copy of ser.num. and the 3 to check numbers are correct
I press * for A33--zone -A33
I press 20 then * zone type- b20
I press 01 for 10 then * report code -c10
I press 5 then * Input code-d5
I press 4 then * loop num.-E4
I press 2 for copy of ser. num. then I press 3 to check serial numbers and they are correct.

zone A30
zone type b23
Report code c10
Input code d5
Loop number E1L
1AL

zone A31
zone type b22
Report code c10
Input code d5
Loop number E2L
1AL

zone A32
zone type b21
report code c10
Input code d5
Loop number E3L
1A1

zone A33
zone type b20
Report code c10
Input code d5
Loop number E4L
A1L

This is how it looks on the panel still I can't get it to respond.What do you think ?

To start
4112 800 then *56
I press 30 then * -zone-A30
I press 23 then *-zone type-b23
I press 01 for 10 then *-Report code-c10
I press 5 then *-Input code-d5
I press 1 then * Loop number-E1 -press * 1A
I then press 1 and get 1b I enter the _ _ _ _ _ _ _ seven serial numbers then * then I press the 3 to check the serial numbers to make sure they are correct and they are the ones I entered
Then I press * because A31 is there .Zone -A31
Then I press 22 then * zone type-b22
I press 01 for 10 then * report code-c10
I press 5 then * Input code-d5
I press 2 then * Loop number-E2
I then press 2 for copy of the serial number then I press 3 to check ser.num. and they are correct.
I press * at A32--zone-A32
I press 21 then * zone type-b21
I press 01 for 10 then * Report code-c10
I press 5 then * Input code-d5
I press 3 then* Loop num.-E3
I then press 2 for copy of ser.num. and the 3 to check numbers are correct
I press * for A33--zone -A33
I press 20 then * zone type- b20
I press 01 for 10 then * report code -c10
I press 5 then * Input code-d5
I press 4 then * loop num.-E4
I press 2 for copy of ser. num. then I press 3 to check serial numbers and they are correct.

zone A30
zone type b23
Report code c10
Input code d5
Loop number E1L
1AL

zone A31
zone type b22
Report code c10
Input code d5
Loop number E2L
1AL

zone A32
zone type b21
report code c10
Input code d5
Loop number E3L
1A1

zone A33
zone type b20
Report code c10
Input code d5
Loop number E4L
A1L

This is how it looks on the panel still I can't get it to respond.What do you think ?
I think I'm doing this right maybe the keyfob has a problem ? If anyone has a clue please let me know .Thanks

Your zone types are correct and even if you had incorrect lloop numbers matched with the buttons the fob should still work. I have ran into some of them with the wrong serial number printed. If you have a panel that you can learn them into and view the serial number try that.