Electronic Alarms and Home Security Devices - Ademco Key pad not Powering up

I have an Ademco Vista 20P alarm I wanted to add a 3rd keypad Ademco 6137B in my Master bedroom. When I wired it up I get no Power.
I did a Continuity test and all 4 wires are ok.
I attached the Keypad DIRECTLY to the 4219 Expansion module which is powered by the Control Panel and 6137B powered up Fine.
I then tested the Volts In the master Bedroom I am receiving 13.5 Volts from the Positive & Negitive and I am receiving 12.9 Volts from the Data in & Date out.
I have set the address of the 6137B to 18.
Any Idea why I it will not Power up????
Jacob:wall:

Ok

Do The Lites Come On Behind The Keypad Numbers And No Lcd Display
If So You Need To Get In To Programing And Turn On Keypad Address 18

If You Want To Test The Keypad
Go To Kp #1 Or #2 Press 1&3 At The Same Time And Look At The Address And Make It 18 And Make The New Kp The Address Of The Other Kp If This Works Then You Know The New Kp Works Then You Know You Need To Go In Programing For This You Need The Master Code To See If You Have The Master Code Type In Your Code And 800 After It Like This (1234800) If You Get 20 On The Kp You Are In Then Hit *99 To Exit Then Let Me Know

as I stated in my question Iset it to 18 ( when i had it hoked up directly to the alarm panal)
so it is set at 18
the lights do not go on at all on the back of the circut board
Jacob:wall:

Ok

What Are Powering From The System


Amount Of

Smokes=
Pirs=
Keypads=2
Expansion Modules=1?

And How Long Is Wire Run Fothe 3rd Keypad

I am still installing
so there ar no smoke
I don't know what PIR's are
2 keypads
1 4219
6 zones are in use
2 exit/entry
4 burglar
the run from the basement to the master BDRM is less then 30ft

I am getting Power I tested the lines 13.5 volts on the +/- and 12.9 on Data In/Out
are those volts correct
Jacob:wall:

Pir Is A Motion Detector

If You Want Me To Call You Just Pm Me With Your Phone No.#

You need to activate keypad address 18 in the system programming, location *191 1 0, or it will not display anything. You have to do this from another keypad that is currently working.

thank you that worked
But I have an "OC" on the display I assume its because of below

I have on my 6160V "FAULT 104 VOICE MODUELE"
I had that once before and I went to the Comm program and deleated all phone #s
I do not have a CS yet
I also unpluged the power to the 4286 & reset the whole system yet the "FAULT 104 VOICE MODUEL"
is still there.
Jacob:wall:

Go to program: in field *28 enter 00 then exit programming. If you aren't going to use the 4286 module, you have to remove it from the system program.

thank you that worked
But I have an "OC" on the display I assume its because of below

I have on my 6160V "FAULT 104 VOICE MODUELE"
I had that once before and I went to the Comm program and deleated all phone #s
I do not have a CS yet
I also unpluged the power to the 4286 & reset the whole system yet the "FAULT 104 VOICE MODUEL"
is still there.
Jacob:wall:

I think OC means open circut,I had the same thing on my keypad when I had the send and receive reversed,Just a thought:coffee:

Thank you all
this Fourm is the best

My keypads are working and the "OC" & "Voice Module 104" errors are gone

I know as I get futher into setting up the system I will have questions.


Thank you all again

Jacob:) :D

For the future questions:wall: