Kitchen Large Electric Appliances - dryer overheat?
Doityourself.com community forum was created to provide answers to all questions related to home improvement and home repair. Doityourself community can help you find information about how-to topics on small fixes to large remodeling projects. With comprehensive how-to content and expertly moderated community forums DoItYourself.com makes it easy to tackle even the most complex home improvement projects.View Full Version : dryer overheat?
HotBacon
09-19-04, 08:33 AM
Maytag stacked washer/dryer combo...not sure of the model number, all it says is Heavy Duty and Computer Touch Control...best guess would be about 15 years old.
The dryer used to be able to dry several loads, then when another was put in the cycle wouldn't start. You could hear a hum...no spinning, no heat, etc. Recently it started not even getting through one load. About 2 minutes left in the cycle you hear a hum start, then it stops. It is unable to be restarted until things cool down.
Any idea where to start looking?
The dryer used to be able to dry several loads, then when another was put in the cycle wouldn't start. You could hear a hum...no spinning, no heat, etc. Recently it started not even getting through one load. About 2 minutes left in the cycle you hear a hum start, then it stops. It is unable to be restarted until things cool down.
Any idea where to start looking?
Sharp Advice
09-19-04, 10:39 AM
Hello: HotBacon
2 of several possibilities come to mind. Dryer motor overheating or the exhaust venting system is clogged or restricted.
Check the venting system first. To verify if this is or is not the problem, remove all the existing vent from the dryer. The end result will be the dryer is not connected to the venting system.
Once you have done this, dry a load of clothing and note the findings. If the dryer operates correctly and the current problem appears to be resolved, the venting system is restricted and or clogged.
Clearing it by any means necessary will resolve the problem. Check the entire system. This also includes the exhaust vent hood outside. It has a flapper that may not be opening fully or not at all. Locate any restriction within the entire exhaust system and clean out all lint. Replace exhaust vent tubing as needed.
At the back of the dryer on the exhaust vent tube there may be what is known as a "Thermal Fuse." This part could be defective. A continuity test can be done on this part. The reading value should be closed {a connection} or the part is considered defective.
The electric motor may also be the problem cause. Electric motor may be overheating and shutting down. If this is suspected, remove the move and have it tested any any local electric motor repair shop.
Safety Reminder:
ALWAYS be positive you have unplugged the electrical power and turned off the gas supply to the appliance prior to attempting any repairs!
TIP:
Best method to determine if any part is funtioning correctly is to carefully remove the part or parts you suspect to be the potential culprit, and have the local appliance parts store person run any required tests.
Read the other questions within this forum on the subjects of dryers for further information. The information contained within the already asked questions contain all the required information.
If you need further assistance, use the reply button to add any additional information or ask additional questions after attempting the correctional method or methods offered. Be sure to post back the results of your findings before asking additional questions.
If the information contained herein does not resolve the problem, we can than move onwards to more detailed and difficult problem possibilities and solutions.
Helping Out Here Too.
Web Site Host, Forums Monitor & Multiple Topics Moderator.
Natural Gas Appliance Diagnostics Technician.
Personal Reminder:
Buckle Up & Drive Safely.
"The Life You Save, May Be Your Own."
2 of several possibilities come to mind. Dryer motor overheating or the exhaust venting system is clogged or restricted.
Check the venting system first. To verify if this is or is not the problem, remove all the existing vent from the dryer. The end result will be the dryer is not connected to the venting system.
Once you have done this, dry a load of clothing and note the findings. If the dryer operates correctly and the current problem appears to be resolved, the venting system is restricted and or clogged.
Clearing it by any means necessary will resolve the problem. Check the entire system. This also includes the exhaust vent hood outside. It has a flapper that may not be opening fully or not at all. Locate any restriction within the entire exhaust system and clean out all lint. Replace exhaust vent tubing as needed.
At the back of the dryer on the exhaust vent tube there may be what is known as a "Thermal Fuse." This part could be defective. A continuity test can be done on this part. The reading value should be closed {a connection} or the part is considered defective.
The electric motor may also be the problem cause. Electric motor may be overheating and shutting down. If this is suspected, remove the move and have it tested any any local electric motor repair shop.
Safety Reminder:
ALWAYS be positive you have unplugged the electrical power and turned off the gas supply to the appliance prior to attempting any repairs!
TIP:
Best method to determine if any part is funtioning correctly is to carefully remove the part or parts you suspect to be the potential culprit, and have the local appliance parts store person run any required tests.
Read the other questions within this forum on the subjects of dryers for further information. The information contained within the already asked questions contain all the required information.
If you need further assistance, use the reply button to add any additional information or ask additional questions after attempting the correctional method or methods offered. Be sure to post back the results of your findings before asking additional questions.
If the information contained herein does not resolve the problem, we can than move onwards to more detailed and difficult problem possibilities and solutions.
Helping Out Here Too.
Web Site Host, Forums Monitor & Multiple Topics Moderator.
Natural Gas Appliance Diagnostics Technician.
Personal Reminder:
Buckle Up & Drive Safely.
"The Life You Save, May Be Your Own."